Bus defrosters for the wiper parking area
Put the heat low along the bottom of the front windshield
Clear View II Front Wiper Parking Area defrosters melt snow and ice low along the bottom of the front windshield to limit snow build up and stop wiper freezing even in the toughest weather.
Developed and tested in Colorado’s tough winter conditions these new defrosters work with the vehicles existing hot air defroster to stop wiper freezing, improve wiper operation and enhance the view of the road ahead.
Put the heat low on the front windshield
Clear View Front Wiper Area Defrosters safely defrost the area at the bottom of the front windshield in the wiper parking area.
Now with high density (HD) heating element spacing for better defrosting. Available for single and two piece windshields.
Clear View II Front Wiper Parking Area Defrosters provide enhanced defroster performance along the bottom of the windshield in the wiper parking area.
Cost effective and easy to install, these new defrosters bond directly to the window to match the heating performance of factory installed defrosters, melting snow and ice in minutes
Keep wipers moving
Enhanced wiper area heating complements the existing hot air defroster effectively eliminating wiper freezing and reducing snow build-up even in the most challenging winter conditions.
Front Wiper Parking Area Defrosters are now available for full and split glass windshields. Edge defrosting in the wiper push area are also now available.
Single and Two Piece Windshields
The Clear View Bus Wiper Parking Defrosters are available for single and split glass windshields. Two iece defrosters use a single ThermaSync control to operate both heated sections from a single switch
Defrost low on the front window
The vehicles hot air defroster clears the area directly in the drivers line of sight about mid way up the windshield in line with the drivers line of sight.
Clear View Front Wiper Area Defrosters put a measured safe heat low on the front windshield below where normal hot air defrosters warm the glass.
How they work
The defroster elements are sandwiched between two pieces of release paper that when separated allow perfect alignment on the glass. Defrosting is accomplished through contact between the Clear View defroster elements and the window.
The defroster is connected electrically through the buss bar tabs and activated with the automatic ThermaSync defroster control and switch.
Defrost the wiper push area
In tough winter conditions wipers can push snow into areas at the sides of the windshield. This snow build up can limit wiper movement and interfere with visibility. Clear View II Side Defrosters put the heat along the edge of the windshield melting snow and ice in this critical area.
The heating elements come on pre-spaced rolls which are trimmed for a custom fit when installed. The self-adhesive heating elements bond directly to the glass and connect to the defrosters side buss bars.
A cover is then applied to the buss bars for a finished factory appearance. The side buss bars include integral tabs are positioned for easy connection to the ThermaSync® defroster control.
A cover is applied to the buss bars for a finished factory appearance. Heating elements match the brownish color of factory defrosters and adhere directly to the glass for improved visibility and safe winter driving. No backing is left on the window to fade, crack or yellow over time.
The automatic shut off is set to 20 minutes as standard. For different timer options please call in your order.
Bus Front Wiper Parking Area Defrosters – Single Piece Windshields
Clear View Bus Wiper Parking Area Defrosters include eight heating elements measuring 6 3/8 (16) inches in height. Minimum length is 68 inches, maximum 84. Connection tabs are both on the same side fro easy wiring. 12 Volts. Twenty minute automatic shut off. Installation ready.
Bus Front Wiper Parking Area Defrosters – Two Piece Windshields
Clear View Bus Wiper Parking Area Defrosters include eight heating elements measuring 6 3/8 (16) inches in height. These are designed for two piece windshields. Minimum length for one side is 34 inches with a maximum of 50. Connection tabs are both on the same side for easy wiring. 12 Volts. Twenty minute automatic shut off. Installation ready.
Defroster controls with smarts
Clear View defrosters use 2812 ThermaSync controls which provide several options including operation of multiple defrosters with a single switch plus a range of automatic timing options from ten minutes to continuous operation. ThermaSync 2812/2824 and the Switch Boss which allows several defrosters to operate from a single switch.
More on ThermaSync Defroster Controls
Delivered ready to install, Clear View Front Wiper Defrosters are complete with ThermaSync defroster control and switch plus an installation pack including wiring harness, under dash mount, fuse and holder, mounting screws, connectors and and other installation accessories plus fully illustrated instructions.
More on Defroster Installation Pack
The Switch Boss allows two or more defrosters to be operated from a single switch ideal installing multiple defrosters in a cab. For example the vertical wiper push defroster and the front wiper parking area defroster can be networked together for single switch operation. Up to four defrosters can be networked using Switch Boss. Requires 2812/2824 TheramSync controls.